FC-PSU-240516 Honeywell Power Supply | 20-32VDC Input, 12-Month Warranty

FC-PSU-240516 Honeywell Power Supply Module

The FC-PSU-240516 is a Honeywell power supply module for industrial control systems. It delivers a stable 5 VDC output at 16 A. The module accepts a wide 20–32 VDC input and draws up to 5.2 A. Honeywell builds this unit as an FS-type non-conformal coated module. That coating helps resist dust and moisture in harsh plant rooms. The design suits continuous duty in process and factory automation. Engineers use it to replace failed or obsolete power modules without redesigning the panel.

Technical Specifications

Measurement range: fixed 5 VDC output rail. Frequency response: not specified for this DC module. Sensitivity: stable regulation under 16 A load. Linearity: tight output control across the 20–32 VDC input window. Resolution: not applicable to this power module. Temperature range: -5°C to +70°C operating. Environmental tolerance: non-conformal coating resists humidity and dust. Noise immunity: designed for industrial control cabinets with high EMI.

Installation Guide

• Confirm the backplane slot matches the FC-PSU-240516 footprint.
• Check the input feed stays within 20–32 VDC.
• Size the input breaker for at least 5.2 A.
• Verify the load does not exceed 16 A at 5 VDC.
• Keep airflow clear around the module in the cabinet.
• Torque terminal screws to the panel vendor spec.
• Power up and measure the output rail before connecting loads.

Commissioning and Maintenance

Commissioning is simple. Apply input power and check the 5 VDC output. Then add load in steps. Maintenance needs no special tools. Inspect the coating for cracks. Clean dust from the heatsink area. Re-seat the module if the output drifts. Keep spare units on hand for fast swap-out.

Compatibility Notes

The FC-PSU-240516 fits Honeywell FS-type racks. It suits systems that need a 5 VDC / 16 A rail. Verify the rack wiring and load budget before you install. This module supports legacy control systems where original parts are hard to find. Contact our team to confirm your chassis revision.

Certification and Compliance

The module follows Honeywell industrial build standards. The FS-type coating supports use in demanding plant environments. Full certification details ship with each unit. Ask our team for the datasheet on request.

Why Buy From Oiltech Controls?

• 15+ years in industrial automation spare parts
• Worldwide shipping through FedEx, UPS and DHL
• Tested surplus and refurbished options available
• 12-month warranty on every unit
• Technical check before dispatch
• Support for obsolete control systems

Typical Applications

Use this module in process control racks. It also fits factory automation panels and legacy Honeywell systems. It suits power rails for I/O cards and field interfaces. The wide input range helps in plants with 24 VDC bus feeds.

Diagnostics Capability

The output rail gives the main health signal. A low rail points to input sag or overload. A hot module points to blocked airflow. Swap the unit to isolate faults fast. Our team helps with fault tracing by email or WhatsApp.

Packing List and Warranty

• 1 x Honeywell FC-PSU-240516 power supply module
• Protective packing for safe transit
• 12-month warranty
• Shipping by FedEx, UPS or DHL

FAQ

Q: What is the output rating?
A: 5 VDC at 16 A.

Q: What input voltage does it need?
A: 20–32 VDC at up to 5.2 A.

Q: Is the module coated?
A: Yes. It is an FS-type non-conformal coated module.

Q: What is the operating temperature?
A: -5°C to +70°C.

Q: Do you ship worldwide?
A: Yes. We use FedEx, UPS and DHL.

Q: Is a warranty included?
A: Yes. Every unit carries a 12-month warranty.

Questions? Email us at info@oiltechcontrols.com or call +86 158 8020 0923 on WhatsApp.

Copyright © 2026 Oiltech Controls Limited. All rights reserved.

Original Source: https://www.oiltechcontrols.com/

All rights reserved.