Product Summary
The Bently Nevada 330905-02-12-05-02-CN is a vibration sensor with M10X1 thread for machinery monitoring. New in box with 1-year warranty. Works with old 3300 RAM probes but has stronger chemical protection.
Key Details for 330905-02-12-05-02-CN
- Part Codes: -02 (20mm unthreaded), -12 (120mm case), -05 (0.5m cable), -CN (China approved)
- Accuracy: ±0.06mm error across 1.5mm range
- Response: 10kHz max with 305m cables
- Output: 7.87V/mm (±12.5%)
Quick Specs
- Cable Data:
0.066Ω/m shield,
69.9pF/m capacitance - Installation:
1.0mm gap,
7.5N•m max torque - Durability:
-52°C to +177°C,
25.4mm bend limit
What’s Included
- Probe with PPS plastic tip
- Stainless steel case (AISI 304)
- ClickLoc connector cable (0.5m)
Important Notes
- Use 24 AWG shielded wire for best signal
- Sealed with Viton O-ring (not pressure tested)
- For small shafts (<13mm), reduce gap to maintain accuracy
Document Download Here:3300 XL NSv Proximity Transducer System Datasheet
When choose NSv reverse-mount over front-mount?
Select 330905 NSv reverse-mount when shaft front is physically inaccessible or front-mount probes interfere with rotor end caps, thrust washers, or keyways; NSv measures through side of precision-targeted 3300 NSv shaft collar with minimal rotor disassembly — standard for retrofit vibration monitoring on aging machinery.
- Mount: side-entry to NSv collar, no front access
- Range: 200 mil peak-to-peak (GFK-20200 §3)
- Requires: 3300 NSv shaft collar (separate)
Same proximitor/cables as 330104/330171?
No — 330905 NSv family has dedicated 3300 NSv proximitor (33080x series) and purpose-designed cable harness; electrical specs similar (-2 V to +18 V output, -17.5 to -26 V DC supply) but construction/impedance differ, causing 15-25 percent calibration error and reduced temperature-cycling stability if mixed.
- NSv proximitor: 33080x (not 330180)
- Output: -2V to +18V DC (same as XL)
- Calibration mismatch risk: 15-25 percent (Bently field note 2019)
Shaft collar prep before install?
Install matching 3300 NSv collar on target shaft end per collar instructions — must be concentric to <= 0.02mm TIR and secured with locking grub screws; set probe gap at 1.0mm to collar precision-targeted face; verify gap with feeler gauge before tightening lock nut to 8 Nm / 71 in-lb.
- Collar concentricity: <= 0.02mm TIR
- Probe gap to collar: 1.0mm nominal
- Lock nut torque: 8 Nm / 71 in-lb
Frequently Asked Questions About the 330905-02-12-05-02-CN
Retrofit existing 3300 XL front-mount with NSv on same 3500 channels?
Yes — 3300 NSv proximitors compatible with 3500/3300 XL racks; each channel firmware must switch from XL to NSv mode via rack config software. Replace 330180 with 33080x NSv proximitors and install NSv shaft collars on each shaft.
Why not drill new hole for front-mount 330104 instead of NSv?
Drilling new probe hole through bearing housings requires disassembly, specialized machining, facility safety sign-off — costs often USD 5,000–15,000 per point. NSv avoids machining entirely (collars mount on existing shaft ends) and installs in 4–6 hours per point, saving 60–80 percent of field cost.
Explore the Bently Nevada 3300 Series










Reviews
There are no reviews yet.