DL100-12HA2101 | SICK Dx100 Standard Laser Distance Sensor
The DL100-12HA2101 is a SICK Dx100 Standard series laser distance sensor. It uses phase shift optical time-of-flight measurement. Its range reaches 130 m on Diamond Grade reflective tape. An integrated heating system keeps it running down to -40 °C. That makes it a practical fit for cold storage and ASRS cranes.
In short, this model trades 300 m reach for cold-room readiness and SSI output. Contact info@oiltechcontrols.com or +86 158 8020 0923 for stock and lead time.
Oiltech Controls Review
- The DL100-12HA2101 targets cold-storage ASRS, not general factory floors.
- Heating draws 25 W to 35 W, so plan your power budget early.
- SSI Gray or binary output suits older PLC racks and retrofits.
- Repeatability holds at 0.5 mm, even at low temperatures.
- Heavier at 1,000 g, so check bracket load ratings.
Oiltech Controls’s Insight
- Buy this model only if you need sub-zero operation.
- For ambient warehouses, the 300 m PROFINET version costs less per meter.
- SSI needs shielded cable runs under 100 m for clean clocks.
- Verify the heating element works before winter deployment.
- Ask us for a firmware and part number cross-check first.
Best Suited Equipment
- Cold-storage automated storage and retrieval systems (ASRS)
- Freezer aisle cranes and stacker cranes
- Deep-freeze conveyor positioning axes
- Retrofit projects with SSI-based PLC racks
- Outdoor docks and unheated warehouses
Technical Data
- Brand: SICK
- Model: DL100-12HA2101
- Series: Dx100
- Part Number: 1059964
- Family: Dx100 DL100 Standard
- Measurement Principle: Phase shift optical time-of-flight laser distance measurement
- Measuring Range: 0.15 m to 130 m on Diamond Grade reflective tape
- Light Source: Visible red laser diode, 658 nm, Class 2
- Laser Class: Class 2 per IEC 60825-1:2014 and EN 60825-1:2014
- Optical Power: Below 1 mW average
- Output Time / Measurement Cycle: ≥ 1 ms internal rate; fieldbus cycle dependent
- Repeatability: 0.5 mm to 1 mm, typical 0.5 mm at 1 σ
- Accuracy: Typical ± 2 mm to ± 3 mm
- Max Tracking Velocity: 15 m/s
- Max Acceleration: 15 m/s²
- Fieldbus Interface: SSI, Gray or binary code
- Digital Outputs: 2x push-pull, PNP/NPN configurable, ≤ 100 mA
- Multifunctional Input: MF
- Supply Voltage: DC 18 V to 30 V, reverse-polarity protected
- Power Consumption: Typical 25 W to 35 W with heater active
- Power Connection: Male M12 4-pin, A-coded, SPEEDCON
- SSI Connection: Female M12 8-pin
- Operating Temperature: -40 °C to +55 °C with heating active
- Storage Temperature: -40 °C to +75 °C
- Protection Rating: IP65 per EN 60529
- Dimensions (W x H x D): 69.4 mm x 82.5 mm x 100.2 mm
- Housing: Aluminum die-cast with PMMA optical window
- Weight: Approx. 1,000 g
Why Buy From Oiltech Controls?
- Our team has handled industrial automation spares for over 15 years.
- We ship worldwide through FedEx, UPS, and DHL.
- Tested surplus and refurbished units are available on request.
- Every eligible order carries a 12-month warranty.
- We verify part numbers and firmware before dispatch.
- Legacy and obsolete control systems are our daily work.
Order, Warranty and Shipping
- Warranty: 12 months on eligible products.
- Dispatch: 24 to 28 hours after order confirmation.
- Couriers: FedEx, UPS, DHL.
- Packing: Anti-static bag, foam, and double-wall carton.
- Tracking: Sent by email once the parcel leaves our warehouse.
FAQ
Q: Can I use the DL100-12HA2101 in a normal warehouse?
A: Yes, but the heater still draws 25 W to 35 W. If you do not need -40 °C operation, the standard PROFINET model is more efficient.
Q: How do I know the SSI output matches my PLC card?
A: Check whether your card reads Gray or binary code. This sensor supports both. Send us your card model and we will confirm before shipping.
Q: Why does the weight matter for installation?
A: At roughly 1,000 g, the unit is heavier than non-heated versions. Use a rigid bracket and check the crane arm load rating.
Q: What cable length is safe for SSI?
A: Keep shielded SSI cable runs under 100 m. Longer runs risk clock errors and unstable position data.
Q: How should I test a used or refurbished unit?
A: Power it at 24 V, check the LC display, confirm heater warm-up, then test SSI data against a known target. We do this before shipment.
Contact
Email: info@oiltechcontrols.com
WhatsApp: +86 158 8020 0923
Copyright © 2026 Oiltech Controls Limited. https://www.oiltechcontrols.com/ All rights reserved.
Reviews
There are no reviews yet.