1. Product Identity & Core Function
- Model: IS200DAMEG1A – GE Mark VIe series.
- Acronym: DAME (Gate Driver Amplifier/Interface).
- Role: Interfaces between control rack and IGBT switching devices for low-voltage drives.
- Key trait: No amplification; direct interface without power inputs.
- Drive rating: 65-frame power class.
2. Technical Data – Compact Reference
- IGBT per phase leg: 1 module (CM100TF-28H Powerrex).
- Boards per drive: 1 board serves all three phases.
- Pin count: 6 connectors with unique labeling.
- LED indicators: None.
- Manual: GEI-100262A.
- Power supply inputs: +15 / -7.5 V (no onboard fuses or test points).
3. Hardware Interfacing & Phase Legs
- BPIA connectivity: 3 dedicated connectors – CPL (phase C, marked U), BPL (phase B, marked V), APL (phase A, marked W).
- Pin 5 function: _PCOM – common emitter for upper/positive IGBT phases.
- Module sharing: Single IGBT module used across all three phase legs.
- No configurable items: Fixed interface, no jumpers or switches.
4. Installation & Replacement – Critical Warnings
- Soldered assembly: IGBT and DAME board are soldered together – replace both as a unit.
- Safety: De-energize control before removal/insertion to prevent shock.
- Mounting steps: Use Dow Corning 340 grease (6 mils min) on heatsink; torque bolts to 40 in-lbs in diagonal sequence.
- Flex circuit: Secure inner and outer flex circuits with nuts/washers after module placement.
5. Output Architecture & Signal Paths
- Simplex outputs: Single-ended, non-redundant signal lines.
- TMR outputs: Three independent controller signals blended by voting hardware.
- Relay voting: Critical protective signals use 3 relays with 6-contact voting layout.
- Output types: Individual I/O networks or combined direct signals.
6. Protection & Signal Conditioning
- Overvoltage & short-circuit protection built-in.
- Electrical isolation between input and output.
- Amplification: None (direct pass-through interface).
- Input from sensors/switches – low-level signals passed to control system.
7. Compatible Equipment & Applications
- GE Mark VIe drive control systems.
- Low-voltage drives with 65-frame power rating.
- Innovation Series racks and BPIA boards.
- Used in turbine, generator, and industrial motor control.
8. Oiltech Controls Review – Expert Insight
- Reliability: Field-proven in GE Mark VIe systems; solder joint integrity is critical – always replace IGBT+board as a set.
- Common failure: Gate drive signal loss often traced to solder cracks; visual inspection before re-installation is advised.
- Spare strategy: Stock at least one pre-tested assembly to minimize downtime during emergency repairs.
9. Professional FAQ – Selection & Experience
- Q: Can I replace only the IGBT without the DAME board?
No. They are soldered together; replace as a matched pair to avoid intermittent gate drive issues. - Q: How do I verify compatibility with my drive?
Check your drive frame size – this board is rated for 65-frame. Also confirm BPIA connector labels match APL/BPL/CPL. - Q: What tools are needed for mounting?
Allen wrench (for 4 bolts), torque wrench (40 in-lbs), and hex drivers for stud nuts. Use silicone grease for thermal contact. - Q: Is this board suitable for TMR systems?
Yes, it supports simplex and TMR output paths; the board itself is passive, but system voting handles redundancy. - Q: What is the typical lead time for a tested replacement?
Oiltech Controls offers 24-28 hour dispatch for stocked units, with FedEx/UPS/DHL global shipping.
10. Why Buy From Oiltech Controls?
- 15+ years focused on industrial automation spares.
- Worldwide shipping via FedEx, UPS, DHL – 24-28 hour dispatch.
- Supplies tested surplus / refurbished modules with verified function.
- 12-month warranty against defects.
- Pre-shipment technical verification – each board checked on test bench.
- Expert support for obsolete control systems including legacy GE drives.
Contact:
info@oiltechcontrols.com
|
+86 158 8020 0923 (WhatsApp)
Copyright © 2026 Oiltech Controls Limited. https://www.oiltechcontrols.com/ All rights reserved.
Diagnostic tip: Check pin 5 (_PCOM) for common emitter continuity. No LED indicators – use multimeter for gate signal validation.










Reviews
There are no reviews yet.